1. Outdoor display installation precautions
(1) Installation of lightning protection devices on displays and buildings
The display main body and the outer casing should be well grounded, and the grounding resistance should be less than 3Ω, which can increase the current discharge.
(2) Waterproof measures for LED display itself
The screen body and the combination of the screen body and the building must be waterproof and leakproof. Since the display screen is often installed outdoors in the sun and rain, the working environment is harsh, so it is necessary to strictly waterproof and moisture-proof. So as not to cause a short circuit, fire, etc.
(3) Circuit chip selection
Industrial-grade integrated circuit chips with an operating temperature between -40 ° C and 80 ° C are selected to prevent the display from starting up as much as possible.
(4) Install ventilation equipment to cool down, keep the internal temperature of the screen is not too high
Since the display screen generates a certain amount of heat during operation, if the ambient temperature is too high and the heat dissipation is poor, the integrated circuit may not work properly or even be burned. Therefore, an axial flow fan is required to discharge heat in time at the top of the screen body.
(5) Super high brightness LED must be selected
In order to increase the contrast, the audience width, and prevent excessive changes in the ambient light, it is necessary to use ultra-high brightness LEDs to ensure long-distance visibility under strong ambient light conditions.
The steel structure on the back of the screen is as follows
The frame part is shown below
Side of the frame, no edging
The installation box is shown below
Display front
2. Precautions for operating the display
(1) Switch sequence
When opening the screen: first turn on the screen, then turn on the screen; when the screen is off: first turn off the screen, then turn off the screen (if you turn off the computer instead of the display, it is likely to cause the display to appear bright, the LED light is burned);
(2) The switch screen should not be too frequent, with an interval of at least 5 minutes;
(3) The computer can be powered on after entering the engineering control software;
(4) Avoid opening the screen in the case of white screen or out of control, because the system has the largest inrush current at this time, and it is easy to cause a short circuit;
(5) When the ambient temperature is too high or the heat dissipation is not good, LED lighting should be careful not to open the screen for a long time;
(6) When a part of the electronic display body appears to be very bright, it is necessary to pay attention to closing the screen in time, and it is not suitable to open the screen for a long time in this state;
(7) If the power of the display often trips, it is necessary to check the screen or replace the power switch in time;
(8) Regularly check the firmness of the joints. If there is looseness, pay attention to timely adjustment and re-reinforcement;
(9) According to the environment of the large screen display screen and the control part, place the pest control medicine;
(10) A large-area power supply can be added to the power segment controller.
Stainless Steel Reversed Dutch Weave
Reverse dutch weave is one of special weave wire cloth used in the filtration field of plastic industry, chemical industry, etc.
Comparing with the normal dutch weave, warp wires are much more than the weft wires in certain unit area, with a larger absolute ratio, so this weave can supply better filtration rate.ustry, etc.
FAQ:
Q1: What problems can I solve for you?
If you have problems in filtering, I can give you suggestions, recommend products and customized solutions.
According to the feedback from my customers, the average life of my product is 10% - 15% longer than that of others.
All specifications are available in stock.
Material are purchased from one of the most famous material company in China.
Equipments are imported from Japan and Germany.
Products have accurate mesh and wire diameter, good roundness to meet all your filtering needs.
Q2: What services can I offer for you?
Every product has passed strict parameter test and element content test, quality inspection report and material list can be provided.
Sufficient inventory, continuous and stable supply, perfect process to avoid mistakes, you can go to bed after you place an order.
Exquisite packaging to protect goods from the damage during transportation.
You can also customize the label or logo.
The status of production and transportation can be provided at any time.
Q3: What are the differences in my factory?
Family business inherits the wisdom of three generations.
Export and supply to export companies for 20 years.
