Research on Micro-miniature Compressed Air Energy Storage System Li Liansheng, Yang Qichao, Zhao Yuanyang (Hefei General Machinery Research Institute National Key in Compressor Technology. Effect of Compressed Specific Pressure Ratio on Compressor and Expander Efficiency In small compressed air energy storage systems, the effect of changes in compressor and expander efficiency on system efficiency at high pressure ratios needs to be considered. It indicates the influence of compressed air storage pressure on the energy storage efficiency and storage density of the system. That is, the storage energy density of the compressed air energy storage system increases with the increase of storage pressure, but the energy storage efficiency of the system increases with the storage pressure. High and gradually reduced. Therefore, the storage pressure of the compressed air energy storage system needs to be optimized based on factors such as system efficiency, energy storage density and operational reliability. The output power of the compressed air energy storage system varies with the flow rate at different pressure ratios. As shown, the compressor power consumption and the expander output power of the compressed air energy storage system increase with the increase of the flow rate and pressure ratio. And the power consumption of the compressor increases at an obvious rate. For a fixed capacity compressed air energy storage system, the flow rate of the expander is determined by the power of the expander and the operating pressure. The ratio of compressor flow to expander flow reflects the charge and discharge time of the compressed air energy storage system. When the flow rate is constant, the volume of the gas storage tank determines the length of the peaking time of the compressed air energy storage system. The larger the volume of the gas storage tank, the longer the peaking time of the system. The maximum efficiency of the system and the minimum tank volume are shown in Table 1. It can be seen from Table 1 that at the same peaking time, as the gas storage pressure increases, the volume of the gas storage tank decreases, but the charging time increases, while the compression power consumption increases, and the energy storage system increases. The efficiency is gradually decreasing. Therefore, the data in Table 1 also indicates that the gas storage pressure of the micro-miniature compressed air energy storage system is closely related to the storage volume, system efficiency and energy storage density. Table 1 Micro-miniature compressed air energy storage system parameters and performance system peaking gas storage charging gas storage tank volume total pressure total expansion system capacity time pressure time reduction work expansion efficiency 3.2 economic analysis 3 micro-miniature compressed air energy storage system and Its key technology 3.1 system scheme China's wind farm single-machine scale is mainly 2MW, MW units, and the development focus is 5MW. If each 2MW or wind power 3MW unit is equipped with micro-miniature compressed air energy storage system, the principle is as follows. In the micro-miniature compressed air energy storage system, the expander (structure type) and generator specifications can be selected according to the power generation power, and the compressor (structure type) and the gas tank size can be selected according to the gas volume and pressure. Micro-miniature compressed air energy storage and its utilization principle The peaking time is calculated according to 15, 0 and 60min. In theory, the economic benefits of compressed air energy storage power station mainly include static efficiency and dynamic benefit. The static benefit is the economic and reliability benefits of the power station when it is responsible for peak filling and energy conversion. The dynamic benefit refers to the economic and reliability benefits embodied in the accidental backup power supply, load standby, etc. due to the adaptability, flexibility and high reliability of the energy storage power station. The main functions of the compressed air energy storage system applied to wind power sites are peak capacity and spare capacity, which reduces the installed capacity requirements of wind power, thereby saving investment and operating costs of wind power equipment. 3.3 Key parameters and technical gas storage pressure and its optimization. Compressed air storage pressure is closely related to the energy density of the power generation system and the efficiency of the energy storage system, and needs to be optimized. In order to increase the pressure and reduce the storage volume, it is necessary to select a compressor unit and an expansion unit of different structural types. Expansion ratio and its control. In the compressed air energy storage system, the expansion process is often in an unstable state, and the change of the inlet parameters has a great influence on the output characteristics of the expander. It is necessary to develop an output performance control technology that meets the requirements of the grid connection technology. System efficiency and related technologies for improving efficiency. To achieve efficient, reliable and stable operation of energy storage systems under variable operating conditions, it is necessary to improve the efficiency of compressors (groups) and expanders (groups), develop system fluidization machinery optimization and control strategies, and thermal management technologies such as compression. Hot recycling and savings. 4 Conclusions A single wind turbine is equipped with a micro-small compressed air energy storage system, which can effectively improve the quality of wind power generation and photovoltaic power generation, and can be used as an emergency power source, which is easy to operate and maintain, and has the least impact on the failure of such equipment; compressed air The storage pressure is a key parameter of the energy storage system, affecting the system efficiency and the storage density. The choice of storage pressure also needs to consider the cost and operational reliability of the system; the design and manufacture of the expander and the expansion ratio control technology are the key to the development of micro-miniature compressed air energy storage systems.
Product Profile Large energy saving ceiling fans are green energy saving products of the 21st century. It has many advantages, such as powerful, no noise, zero pollution, low energy consumption. It is very popular for large masses of users. It is not only mainly used in steel structure plant, logistics warehouse, farm and other large enterprise buildings, but also agricultural markets, gymnasiums, waiting rooms, exhibition halls and other large public buildings. A large energy-saving ceiling fans with a speed of 50 revolutions per minute 1 to 3 meters per second to make the human body feels the best wind speed. A breeze from all directions gently caresses the body and increases the evaporation of human sweat. The cooling effect of 5 to 8 degrees is similar to the comfort presented by the natural breeze, which can not be matched by other fans. It is an ideal choice for indoor, ventilation and cooling in summer to remove humidity and heat. Only seven degrees of electricity per day, it can be cool for a whole summer. Energy saving comparation In summer, the sun shines directly and the indoor temperature is more than 40 degrees on average. Common industrial exhaust fans can only increase the indoor temperature. Industrial air conditioners consume thousands of kilowatts of energy every shift. There is no obvious unenclosed cooling in the space, which also increases the operating cost of enterprises. The emergence of a large energy saving ceiling fan brought the perfect solution. An energy saving fan with a diameter of 7.2meters can push the air to produce a large amount of winds effectively. The continuously rotating blades of circular form an airflow field with an effective area of 600 to 800 square meters. No other device has not yet been compared. The large energy-saving ceiling fan praduced by Linter technology has the characteristics of high reliability, feasibility and low power consumption. The controller unit used the stability of the energy-saving inverter system. In practice, the average power consumption is less than one killowatt per hour. It can guarantee more than 5,000 hours of uninterrupted operation. Linter7200 of a large energy-saving ceiling fan can cover the area of about 50 small fans of 0.75 megabytes worked. In a factory of 9000 square meters, if full coverage is to be achieved, it needs about 300 small fans or industrial 6 energy-saving fans. According to the use of four years, every eight months, every day for ten hours, can be run for 10,000 hours, about 90000kw power consumption, than the small wind 1080000kw, save 990000kw, save energy by 92%. When meeting the extreme high temperature climate, the large energy saving fans and air conditioners are used together, it will be coller. Using A large energy-saving ceiling fan for air supply can not only save the air conditioning tube, but also save more than 30% energy. Attentio Lectotype The building structure: H-shaped steel, I-shaped steel, Mixed steel square bar spherical column spherical structure. The total height of the building is more than 4, 0m, less than 15m. 1, 0m. The minimum distance between the fan and the roof is 1, 0m. The minimum safety distance between the fan blades and the obstacle is 0, 3 m. The distance between the fan blades and the wall on both sides is more than 1, 5 m. Effects of various environments on fan performance. Open space, promotes air circulation. Indoor airflow circulation in enclosed spaces is suitable for use with air conditioning. In a multi-fan environment, due to the low wind speed, caused by the fan, there will be no cyclones. The distance between the two fans will be separated before the wind will not cancel, and the coverage area will be increased at the same time. Company Information HongFa automatic door Technology (Shenzhen) Co., Ltd is a high-tech enterprise which engages in the development of advanced world-class automatic doors. Our main products include industrial fast rolling door, industrial PVC rolling door, industrial PVC rolling door, fast rolling door, rolling door, fast rolling door, rolling door, industrial automatic lifting door, industrial automatic lifting door, automatic vertical hinged door, automatic stainless steel door, automatic doors, automatic doors, electric folding gate, rolling door, automatic doors, automatic doors, automatic doors, automatic doors,
Industrial ceiling fan,electric fan,industrial fan SHENZHEN HONGFA AUTOMATIC DOOR CO., LTD , https://www.hongfahsd.com
May 04, 2023